1.
Input voltage: DC 11V~15V. The working electric current is
less than 6A when it is charged in full load. The current
of the fuse is 10A which could prevent short circuit.
2. The charge current is 0.2A~2.0A in adjusting steps of 0.2A
and is set by the buttons on the board.
3. Controlled by 4 separated internal micro computers. Charge
1S-4S battery separately. There is no other serial charging
+ balancer setup on the market.
4. 4 separated JST style charging ports and one general charging
port.
5. Large LCD display. Real-time display of voltage and charging
processing.
6. Low voltage protection. Charger won't charge any cell if
voltage is lower than 2.7v.
7. Automatically stop charging when it's finished and indicate
with buzzer.
8. 4 separated parallel charging circuits ensure your battery
is 100% fully charged.
9. Charge mode of the balanced parallel connection:
A. charge in parallel connection for a single
cell or four single cells at once.
B. charge in parallel connection for a pile of
two series-wound lithium cells or two piles of
two series-wound lithium cells at once.
C. charge in parallel connection for a pile of
three series-wound lithium cells or one single
lithium cell at once.
D. charge in parallel connection for a pile of
four series-wound lithium cells
10. Workingtemperature rating: -20 ~ 60 C
11. Full circuit protection: protect the charger and battery
even when the battery or the power supply connections are
reversed.
12. General charging port will allow you charge any lipo battery
which has balancing leads.
We
stock only the latest cell technology. Our 1320/3 packs have
the cell balance 4 pin plug. We also have the Thunder Power
cell balancers and Thunder Power chargers in stock
Thunder
Power 1320mah 3 cell 11.1 volt LiPo Battery with cell
balance 4 pin plug. Price $55.00 SPECIFICATIONS Thunder
Power 1320 mAh, 3 cells Pro Lite (11.1V), 4-pin balancer
connector.
Rating: 13C (17A) continuous, 20C (27A) burst
Output: 11.1V Nominal, 1320mAh
Dimension: 1.3" x 2.5" x .75" (3 oz)
Thunder
Power 2100 mah 3 cell 11.1 volt LiPo
Battery. Price
$70.00
SPECIFICATIONS 2100 mAh, 2 cells (7.4V), 4-pin balancer
connector
Rating: 15C (31.5A) continuous, 20C (42A) burst
Output: 7.4V Nominal, 2100mAh
Dimension: 1.3" x 3.86" x .51"
Weight: 3.35 oz
THUNDER
POWER TP425 LITHIUM POLYMER CHARGER The
TP-425 charger is specifically designed to charger Lithium
Polymer batteries only.
Features:
Ultra high speed power system
Light weight and fully capable to charge up to 2500
mah/4 cells in series
Easy setting for various battery pack parameters
Reverse polarity protection circuitry (input/output)
Easy monitoring indicators (current and voltage charge
status)
Beep alerts fault conditions or charge is complete
Safe mode automatic cell count
Specifications:
Input
power source: 11v-15v DC, requires 4 Amps to charge
at maximum rate.
Charge voltage: 3.7 V-7.4 V-11.1 V-14.8V (1 cell - 4
cells in series)
Charge Current: 300mA-500mA-800mA-1300mA-2000mA-2500mA
Full charge voltage: 4.2 V per cell
Size: 1.62" x 4" x 0.62" (42 mm x 102
mm x 16.2 mm) ELE-18 Thunderpower Charger TP-425C $55.00
ThunderPower
cell balancer.
Balances in the TP-ProLite batteries with the second pigtail.
A must to make sure that each cell in your battery packs
are kept in balance. ELE-19
Thunderpower Balancer TP-205 $55.00
Electric Propellers
GWS Hyper Drive..
GWS
Hyper Drive
8 x 4
GWS Hyper Drive
9 x 5GWS Hyper Drive 10
x 8GWS Hyper Drive
11 x 7 GWS Hyper Drive
Blenderm
Tape
Are you tired of the tape coming loose on your electric
flying surfaces? This is the only tape that really works
on all of the foam airplanes for hinging. It is thin,
flexible and has a very aggressive adhesive. It stays
where you put it. Use it on all electric airplanes that
use the tape to hinge the flying surfaces with tape.
Have a roll in your tool box and you can use it as intended
to patch up cut fingers!
1" Width
Carbon
Fiber Tubes
and Rods Click on Image for more carbon fiber Recommended:
060 x 36" Carbon rod
125 x 36" Carbon tube
157 x 36" Carbon tube
188 x 36" Carbon tube
118 x .019 x 36" Carbon flats
Foam
Safe/Oderless CA
Medium 1/2 Oz
SUPER-GOLD™ ELE-74
Foam Safe Oderless CA SUPER-GOLD+™ Thin
1/2 Oz
ELE-72
Bob
Smith IC-2000™ CA
Medium 1/2 Oz CPR-70
Rubber-toughened
cyanoacrylate that forms superior shock resistant bonds
on non-porous surfaces. The black colored CA has added
flexibility for the bonding of metals, fiberglass, rubber,
carbon-fiber and other advanced materials. For model use,
IC-2000™ is ideal for the bonding of bulkheads, formers
and servo rails to the inside of fiberglass hulls and
fuselages. Setup time is 20-40 seconds, which can be accelerated
with INSTA-SET™. When cured, IC-2000™ is pliable enough
to be carved with a hobby knife.
Ca
Activator Foam Safe
CPR-75
These
are 10 ounce cans of a great kicker. You will use it
to the bottom of the can, and that will take you a long
time. The nozzle does not plug and will spray evenly
for the entire can, not turn into a stream. It will
not evaporate while is sitting on your workbench.
I
have not found any foam that it will bother. It also
works on all Ca's. It does not make it turn to "popcorn";
it just makes it cure very quickly.
